DISC dbx 2231 Dual 31 Band Graphic EQ

Full Description

Who knows more about limiting than the folks at dbx; nobody... that's who. So when the guys were developing this new series of EQs they wanted something that would be unique to these EQs. That's when Roger got another one of his bright ideas and said "I bet they'll work a lot better if there's a cool limiter built in." Next thing you know, all the guys are in the studio amazed at the new limiter Roger had designed specially for the 20 Series. Once again, hearing is believing... With a threshold range of 0dbu to plus 20dbu, the patent-pending PeakPlus limiter is designed to tame your program material from the subtlest nuances to the rowdiest hits. Also, the four stage LED ladder gives you a great visual indication as to what the limiter is doing.

20 Series EQs. You used to have to settle for second best in a reasonably priced EQ but not any more. With the new 20 Series from dbx Professional Products you get a great EQ circuit, a graceful yet powerful limiter and the revolutionary new design of the Type III Noise Reduction. Check out the dbx 20 Series graphic EQs at your pro audio outfitter. You'll see, with the 20 Series EQs you get MORE!!!

Features

• Revolutionary instant encode/decode Type III Noise Reduction in-circuit at the push of a button. Increases S/N ratio by up to 20dB
• Patent-pending PeakPlus Limiter threshold range from 0dBu to +24dBu (off) can transparently tame the wildest hits or the subtlest nuances of any signal
• Four segment LED bargraph for BOTH Gain Reduction AND Output Level
• Status LEDs offer visual feedback for all settings on the front panel

Specifications:

INPUT

• Connectors: 1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip
• Type: Electronically balanced/unbalanced, RF filtered
• Impedance: Balanced 40k ohm, unbalanced 20k ohm
• Max Input Level: >+21dBu balanced or unbalanced
• CMRR: >40dB, typically >55dB at 1kHz

OUTPUTS

• Connectors: 1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip
• Type: Impedance-balanaced/unbalanced, RF filtered
• Impedance: Balanced 200 ohm, unbalanced 100 ohm
• Max Output Level: >+21dBu balanced/unbalanced into 2k or greater - >+20dBm balanced/unbalanced (into 600)

SYSTEM PERFORMANCE

• Bandwidth: 20Hz to 20kHz, +/-0.5dB
• Frequency Response: <10Hz to >50kHz, +0.5/-3dB
• Noise Reduction In: (+/-6 and +/-12dB range):
• Signal-to-Noise: >102dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
• Dynamic Range: >120dB, unweighted
• Noise Reduction Out: (+/-6dB range):
• Signal-to-Noise: >94dB, unweighted, ref: +4dBu, 22kHz measurment bandwidth
• Dynamic Range: >112dB, unweighted
• Noise Reduction Out: (+/-12dB range):
• Signal-to-Noise: >90dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
• Dynamic Range: >108dB, unweighted
• THD + Noise: <0.04%, 0.02% typical at +4dBu, 1kHz
• Interchannel Crosstalk: <-80dB, 20Hz to 20kHz
• Noise Reduction: Up to 20dB of dynamic broadband noise reduction

FUNCTION SWITCHES

• Type III® NR: Activates dbx Type III Noise Reduction
• EQ Bypass: Bypasses the Graphic Equalizer section in the signal path
• Low Cut (recessed): Activates the 40Hz 18dB/octave Bessel high-pass filter
• Range (recessed): Selects either +/- 6dB or +/-15dB slider boost/cut range

INDICATORS

• Output Level Meter: 4-LED bar graph (Green, Green, Yellow, Red) at -10, 0, +10, and +18dBu
• Gain Reduction Meter: 4-LED bar graph (all Red) at 0, 3, 6, and 10dB
• Type III NR Active: Yellow LED
• EQ Bypass: Red LED
• Clip: Red LED
• Low Cut Active: Red LED
• +/-6dB range: Yellow LED
• +/-12dB range: Red LED